Chatter Control in Induction Heat Assisted End Milling Год выпуска: 2013Автор: A.K.M. Nurul Amin and Abdelgadir Mohamed MahmoudИздательство: LAP Lambert Academic PublishingСтраниц: 132ISBN: 9783659436543Описание The conventional induction heating method, used for heat treatment of parts has been customized as a novel method for heat assisted machining of metallic materials. This method is very clean and of low cost compared to laser heating. The method is especially applicable in milling operations with high width of cut, which a single laser can not cover and there is a need of employing multiple lasers. Heating time is very short and only the skin of the work piece is heated and removed during machining. Cutting forces are low due to lower yield strength of the materials at elevated temperature, chatter is damped and surface roughness and tool wear are low. This innovative method if applied to the industry would lead to higher productivity and lower cost of machining.
Похожие книги
Yasheng Huang. Inflation and Investment Controls in China: The Political Economy of Central-Local Relations During the Reform Era. – М.: Cambridge University Press, 1999. – 396 с. Charles H. Fine. Clockspeed : Winning Industry Control in the Age of Temporary Advantage. – М.: Basic Books, 1999. – 288 с. Ifip Tc11 Wg11.5 Working Conference on Integrity and Internal Control, Michael Gertz. Integrity and Internal Control in Information Systems V: Ifip Tc11/Wg11.5 Fifth Working Conference on Integrity and Internal Control in Information Systems (Iicis), November 11-12, 2002, Bonn, Germany (International Federation for Information Processing. – М.: , 0. – 0 с. Cornelius E. Tierney, Edward F. Kearney, Roldan Fernandez, Jeffrey W. Green, Michael J. Ramos, Kearn. OMB Circular A-123 and Sarbanes-Oxley: Management's Responsibility for Internal Control in Federal Agencies. – М.: , 2006. – 320 с. Ahmed Abdel-Hamid Zaki Diab,Ahmed Mohamed El-Sawy and Yehia Sayed Mohamed. Vector control of induction motors considering magnetic saturation. – М.: LAP Lambert Academic Publishing, 2012. – 152 с. A.K.M. Nurul Amin,Siti Nurshahida Mohd Nasir and Noor Syairah Khalid. High Speed Ductile Mode End Milling of Silicon with Air Blowing. – М.: LAP Lambert Academic Publishing, 2013. – 148 с. P. Nagasekhar Reddy. Direct Torque Control of Induction Motor Using Random PWM Algorithms. – М.: LAP Lambert Academic Publishing, 2014. – 168 с. A.K.M. Nurul Amin,Mohd Dali Bin Mohd Ismail and Muhammad Iqbal Bin Musa. High Speed End Milling of Single Crystal Silicon Wafer. – М.: LAP Lambert Academic Publishing, 2011. – 96 с. Langsi Yao. Vector Control of Induction Motor Using MATLAB. – М.: LAP Lambert Academic Publishing, 2012. – 112 с. Jackson G. Njiri,Bernard W. Ikua and George N. Nyakoe. Optimization of machining parameters for ball-end milling. – М.: LAP Lambert Academic Publishing, 2011. – 108 с. A.K.M. Nurul Amin and Abdelgadir Mohamed Mahmoud. Chatter Control in Induction Heat Assisted End Milling. – М.: LAP Lambert Academic Publishing, 2013. – 132 с. A.K.M. Nurul Amin and Mohammad Ishtiyaq Hossain. Induction Heat Assisted End Milling of Inconel 718 and Ti6Al4V Alloys. – М.: LAP Lambert Academic Publishing, 2013. – 196 с. Chigbogu Ozoegwu. Theory of Curvature Effects on End-Milling. – М.: LAP Lambert Academic Publishing, 2013. – 92 с. A.K.M. Nurul Amin. Heat Assisted Machining of Hardened Steel AISI H13. – М.: LAP Lambert Academic Publishing, 2012. – 172 с. A.K.M. Nurul Amin and Mohammed Anayet Ullah Patwari. Resonance Effect in Chatter Formation in Metal Cutting. – М.: LAP Lambert Academic Publishing, 2011. – 264 с. Wang Xin,Bogdan Miedzinski and Xu Liangjun. A low frequency of induction heating for continues welded rails. – М.: LAP Lambert Academic Publishing, 2010. – 124 с. Binbin Zhou,Jiannong Cao and Bai Li. Adaptive Traffic Light Control In WSN-Based ITS. – М.: LAP Lambert Academic Publishing, 2012. – 156 с. Образцы работ
Задайте свой вопрос по вашей теме
Контакты
Поделиться
Мы в социальных сетях
Реклама
Отзывы
Владимир Консультацию получил, спасибо за проделанную работу в сложных условиях!
