Написать рефераты, курсовые и дипломы самостоятельно.  Антиплагиат.
Студенточка.ru: на главную страницу. Написать самостоятельно рефераты, курсовые, дипломы  в кратчайшие сроки
Рефераты, курсовые, дипломные работы студентов: научиться писать  самостоятельно.
Контакты Образцы работ Бесплатные материалы
Консультации Специальности Банк рефератов
Карта сайта Статьи Подбор литературы
Научим писать рефераты, курсовые и дипломы.


подбор литературы периодические источники литература по предмету

Wound Rotor Induction Generator Scalar Modeling and Control



Год выпуска: 2013
Автор: Mohamed Atef Elsaharty and Walid Ghoneim
Издательство: LAP Lambert Academic Publishing
Страниц: 180
ISBN: 9783659505904
Описание
In the field of electrical power generation, the wind energy is one of the important sources of renewable energy. The main problem with this type of energy is the variable nature of the wind speed. The wound rotor induction generator is used to handle this speed variations by adequate voltage injections in the rotor circuit to maintain the stator voltage and frequency constant irrespective to speed or load variations. This book deals with the analysis, steady state modeling, and control of the wound rotor induction generator that can be used in wind energy applications. Moreover the linear control strategy used is analyzed in terms of all its operating conditions and output quality. The theory was validated via experimental setup to compare theoretical, simulation and practical results to evaluate the usefulness and effectiveness of the system.


Похожие книги

  1. Charles S. Tapiero. Applied Stochastic Models and Control for Finance and Insurance. – М.: , 0. – 0 с.
  2. James Momoh. Operation and Control of Electric Energy Processing Systems. – М.: , 2010. – 202 с.
  3. Ronald R. Yager. Essentials of Fuzzy Modeling and Control. – М.: , 1994. – 408 с.
  4. Om Prakash Bharti. Modeling and Control of DFIG-based Variable Speed Wind Turbine. – М.: LAP Lambert Academic Publishing, 2012. – 68 с.
  5. Salam Abdul and Mafizul Islam. Modelling and Control System design of Heat Pumps. – М.: LAP Lambert Academic Publishing, 2014. – 80 с.
  6. Md. Arifujjaman. Performance and Reliability Comparison of Small Wind Turbine Systems. – М.: LAP Lambert Academic Publishing, 2011. – 216 с.
  7. BENEDITO BONATTO and Hermann W. Dommel. EMTP Modelling of Control and Power Electronic Devices. – М.: LAP Lambert Academic Publishing, 2010. – 196 с.
  8. Raul Santiago Munoz Aguilar. Sliding Mode Control of the Wound Rotor Synchronous Generator. – М.: LAP Lambert Academic Publishing, 2010. – 168 с.
  9. Sebastien Aubouet. Semi-active dampers modeling and control. – М.: LAP Lambert Academic Publishing, 2010. – 200 с.
  10. Danijel Pavkovic and Josko Deur. Modeling and Control of Electronic Throttle Drive. – М.: LAP Lambert Academic Publishing, 2011. – 188 с.
  11. Lei Liu. Modeling, Identification and Control of Hysteretic Dynamics. – М.: LAP Lambert Academic Publishing, 2014. – 172 с.
  12. Carlos Andres Ramos Paja,Alfonso Jose Romero Nevado and Roberto Giral Castillon. Fuel cell modeling and control. – М.: LAP Lambert Academic Publishing, 2010. – 188 с.
  13. Michal Suransky. Modelling, Identification And Control Of Robotic Manipulator. – М.: LAP Lambert Academic Publishing, 2014. – 64 с.
  14. Kalyan raj Kaniganti,Linga Reddy and Kiran Kumar, Vinay. Voltage control of self excited induction generator. – М.: LAP Lambert Academic Publishing, 2012. – 84 с.
  15. Mohamed Atef Elsaharty and Walid Ghoneim. Wound Rotor Induction Generator Scalar Modeling and Control. – М.: LAP Lambert Academic Publishing, 2013. – 180 с.
  16. Moleykutty George,Kartik Basu and Jagadeesh Pasupuleti. Modeling and control of DC drivers using MATLAB/PSB. – М.: LAP Lambert Academic Publishing, 2012. – 56 с.
  17. Viktor Kalman. Modeling and control of omnidirectional wheels. – М.: LAP Lambert Academic Publishing, 2014. – 148 с.

Образцы работ

Тема и предметТип и объем работы
Этапы формирования теории президентства
История государства и права
Курсовая работа
30 стр.
Слияния и поглощения Мировая и Российская практика
Мировая экономика
Диплом
99 стр.
Особенности организации маркетинговой деятельности на предприятии сферы услуг
Маркетинг
Дипломный проект
110 стр.
Математические модели океанических течений
Переводоведение (теория перевода)
Курсовая работа
42 стр.



Задайте свой вопрос по вашей теме

Гладышева Марина Михайловна

marina@studentochka.ru
+7 911 822-56-12
с 9 до 21 ч. по Москве.
Контакты
marina@studentochka.ru
+7 911 822-56-12
с 9 до 21 ч. по Москве.
Поделиться
Мы в социальных сетях
Реклама



Отзывы
Алена, 22.12
Спасибо Вам огромное за помощь! Диплом сдан и защищен на 5!Ваша помощь просто неоценима!